Enerdrive Epower 40A+ DC2DC Battery Charger 12v DC to DC MPPT Solar EN3DC40+

Enerdrive DC 2 DC ePOWER 40A+ DC to DC Battery Charger with MPPT Solar controller EN3DC40+

SKU: EN3DC40+

Availability: In stock

Regular Price: $459.00

Special Price: $399.00

Enerdrive
Skye Finance
Shipping Cost Calculator

Destination

Enter destination to get a shipping cost

Shipping Rates

Product Description

Details

Enerdrive DCtoDC+ 40 / 50amp 12v Battery Charger with MPPT Solar Regulator

Australian Stock with Full Manufacturer Warranty - 2yrs Limited / 3Yrs Pro Rate offered by Enerdrive Australia - Not Grey Import.

The Epower EN3DC40+ is a programmable DC to DC charger featuring separate inputs for engine and solar charging. The solar input is regulated with an MPPT algorithm with a maximum Voc rating of 45V. The charger output is 40A up to 40°C but can be decreased for smaller batteries. While the engine is running the charger will use the engine input, otherwise the solar input will be used for charging. Engine charging is autosensed from the start battery voltage, but an ignition signal can be used instead. Temperature sensor is included.

Installs available in Canberra ACT. Highly recommended DC to DC charger for Lihtium Iron, AGM Deep Cycle & Lead Crystal Batteries.

Features include

• Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output
• DC M6 screw terminals that will allow for large battery cable connection between all sources
• A dedicated Maximum Power Point (MPPT) solar regulator
• The same battery algorithms as included in our AC mains ePOWER battery charger. GEL, AGM, Flooded, Lithium and the ability to create a full custom profile
• Vehicle input allows for either 12 or 24v and a maximum solar input of 45V/800W
• 40A output up to 40+°C with thermo controlled fan cooling
• Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage
• Temperature sensor included in charger for more accurate battery charging

The Enerdrive ePOWER DC2DC+ Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. With two inputs available, the main/house battery will be charged from either the engine while underway, or via the solar panels when stationary. The process to choose either engine or solar is fully automatic and both functions are controlled from within the unit itself without the need for external relays.

During normal operation the ePOWER DC2DC+ Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads.

Enerdrive EN3DC40+ Multi-stage Charging Process

• The ePOWER DC2DC+ Battery Charger is a fully automatic, set and forget charger. It is designed to quickly and accurately recharge your deep cycle batteries utilising charger algorithms that help to maximise the life of your specialised deep cycle batteries.

• The ePOWER DC2DC+ Battery Charger features multistage smart charging technology that enables the charger to be connected to your battery bank permanently. With the input of multiple sources, you can be assured of charging your batteries whenever underway; or when the sun is shining on your solar array.

As dictated by battery manufacturer’s recommendations, deep cycle batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER DC2DC+ smart charger delivers three primary charge stages.

Stage 1 – Bulk or Boost charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery is recovered as fast as possible.

Stage 2 – Absorption Charge; With the charger voltage held steady, the remaining 20% is replaced with the charger allowing the current to taper off as the battery approaches full charge.

Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged, yet allows the charger to supply enough current to make up for the self-discharge losses of the battery, while supporting any additional loads connected to the battery (such as DC lighting and refrigerators). This stage allows for the charger to be used as a DC power supply.

Smart Charging Feature

The ePOWER DC2DC+ Battery Charger will regulate its output based on the loads connected to your battery bank. This function is important to maintain the life of your battery bank as some battery chargers mistake loads for discharge and continue to keep the batteries in the bulk or absorption stage for extended periods of time, which will damage the battery bank. The ePOWER DC2DC+ Battery Charger has two methods of load based regulation to ensure your battery charger transitions to float when it should do so.

Specifications

SKU EN3DC40+
Brand Enerdrive
Product Type 12v 40Amp DC2DC Battery Charger
Maximum Output 40A
Charger Mode Output Voltage 13.8V - 15.5V
Float 13.0V - 13.8V
Equalize 15.5V
Charging Control Three Stages
DC Output Single
Selectable Battery Type Gel, AGM, Flooded, Lithium, Program
Charger Efficiency 95%
Temperature Setting Low/ Normal/ High (Battery Temperature Sensor Standard)
Dimensions (LxWxH mm) 1.85Kg
Model EN3DC40+
NOTE For all installation that requires additional wiring, we recommend you engage a licensed auto electrician.

 

Reviews

Write Your Own Review

You're reviewing: Enerdrive Epower 40A+ DC2DC Battery Charger 12v DC to DC MPPT Solar EN3DC40+

Product Tags

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.